Bituminous sands, colloquially known as oil sands or tar sands, are a type of unconventional petroleum deposit. The sands contain naturally occurring mixtures of sand, clay, water, and a dense and extremely viscous form of petroleum technically referred to as bitumen (or colloquially "tar" due to its similar appearance, odour, and colour). Oil sands are found in large amounts in many countries throughout the world, but are found in extremely large quantities in Canada and Venezuela.
The crude bitumen contained in the Canadian oil sands is described by Canadian authorities as "petroleum that exists in the semi-solid or solid phase in natural deposits. Bitumen is a thick, sticky form of crude oil, so heavy and viscous (thick) that it will not flow unless heated or diluted with lighter hydrocarbons. At room temperature, it is much like cold molasses". Venezuelan authorities often refer to similar types of crude oil as extra-heavy oil, because Venezuelan reservoirs are warmer and the oil is somewhat less viscous, allowing it to flow more easily.
Oil sands reserves have only recently been considered to be part of the world's oil reserves, as higher oil prices and new technology enable them to be profitably extracted and upgraded to usable products. They are often referred to as unconventional oil or crude bitumen, in order to distinguish the bitumen extracted from oil sands from the free-flowing hydrocarbon mixtures known as crude oil traditionally produced from oil wells.
Making liquid fuels from oil sands requires energy for steam injection and refining. This process generates two to four times the amount of greenhouse gases per barrel of final product as the production of conventional oil. If combustion of the final products is included, the so-called "Well to Wheels" approach, oil sands extraction, upgrade and use emits 10 to 45% more greenhouse gases than conventional crude.
The exploitation of bituminous deposits and seeps dates back to paleolithic times. The earliest known use of bitumen was by Neanderthals, some 40,000 years ago. Bitumen has been found adhering to stone tools used by Neanderthals at sites in Syria. After the arrival of Homo sapiens, humans used bitumen for construction of buildings and water proofing of reed boats, among other uses. In ancient Egypt, the use of bitumen was important in creating Egyptian mummies—in fact, the word mummy is derived from the Arab word mĊĞmiyyah, which means bitumen.
In ancient times, bitumen was primarily a Mesopotamian commodity used by the Sumerians and Babylonians, although it was also found in the Levant and Persia. Along the Tigris and Euphrates rivers, the area was littered with hundreds of pure bitumen seepages. The Mesopotamians used the bitumen for waterproofing boats and buildings. In North America, the early European fur traders found Canadian First Nations using bitumen from the vast Athabasca oil sands to waterproof their birch bark canoes. In Europe, they were extensively mined near the European city of Pechelbronn, where the vapor separation process was in use in 1742.
The name tar sands was applied to bituminous sands in the late 19th and early 20th century. People who saw the bituminous sands during this period were familiar with the large amounts of tar residue produced in urban areas as a by-product of the manufacture of coal gas for urban heating and lighting. The word "tar" to describe these natural bitumen deposits is really a misnomer, since, chemically speaking, tar is a man-made substance produced by the destructive distillation of organic material, usually coal. Since then, coal gas has almost completely been replaced by natural gas as a fuel, and coal tar as a material for paving roads has been replaced by the petroleum product asphalt. Naturally occurring bitumen is chemically more similar to asphalt than to tar, and the term oil sands (or oilsands) is more commonly used in the producing areas than tar sands because synthetic oil is what is manufactured from the bitumen.
Oil sands are now considered a serious alternative to conventional crude oil, since crude oil is becoming scarcer. Oil sands and oil shale have the potential to generate oil for centuries.
Many countries in the world have large deposits of oil sands, including the United States, Russia, and various countries in the Middle East. However, the world's largest deposits occur in two countries: Canada and Venezuela, each of which have oil sand reserves approximately equal to the world's total reserves of conventional crude oil. As a result of the development of Canadian oil sands reserves, 44% of Canadian oil production in 2007 was from oil sands, with an additional 18% being heavy crude oil, while light oil and condensate had declined to 38% of the total. Because growth of oil sands production has exceeded declines in conventional crude oil production, Canada has become the largest supplier of oil and refined products to the United States, ahead of Saudi Arabia and Mexico. Venezuelan production is also very large, but due to political problems within its national oil company, estimates of its production data are not reliable. Outside analysts believe Venezuela's oil production has declined in recent years, though there is much debate on whether this decline is depletion-related or not.
Bituminous sands are a major source of unconventional oil. Conventional crude oil is normally extracted from the ground by drilling oil wells into a petroleum reservoir, allowing oil to flow into them under natural reservoir pressures, although artificial lift and techniques such as water flooding and gas injection are usually required to maintain production as reservoir pressure drops toward the end of a field's life. Because extra-heavy oil and bitumen flow very slowly, if at all, toward producing wells under normal reservoir conditions, the sands must be extracted by strip mining or the oil made to flow into wells by in situ techniques, which reduce the viscosity by injecting steam, solvents, and/or hot air into the sands. These processes can use more water and require larger amounts of energy than conventional oil extraction, although many conventional oil fields also require large amounts of water and energy to achieve good rates of production.
This is because heavy crude feedstock needs pre-processing before it is fit for conventional refineries. This pre-processing is called 'upgrading', the key components of which are as follows:
- removal of water, sand, physical waste, and lighter products
- catalytic purification by hydrodemetallisation (HDM), hydrodesulfurization (HDS) and hydrodenitrogenation (HDN)
- hydrogenation through carbon rejection or catalytic hydrocracking (HCR)
As carbon rejection is very inefficient and wasteful in most cases, catalytic hydrocracking is preferred in most cases. All these processes take large amounts of energy and water, while emitting more carbon dioxide than conventional oil.
Catalytic purification and hydrocracking are together known as hydroprocessing. The big challenge in hydroprocessing is to deal with the impurities found in heavy crude, as they poison the catalysts over time. Many efforts have been made to deal with this to ensure high activity and long life of a catalyst. Catalyst materials and pore size distributions are key parameters that need to be optimized to deal with these challenge and this varies from place to place, depending on the kind of feedstock present.
At the present time, only Canada has a large-scale commercial oil sands industry, though a small amount of oil from oil sands is produced in Venezuela. Because of increasing oil sands production, Canada has become the largest single supplier of oil and products to the United States. Oil sands now are the source of almost half of Canada's oil production, although due to the 2008 economic downturn work on new projects has been deferred, while Venezuelan production has been declining in recent years. Oil is not produced from oil sands on a significant level in other countries.
Since Great Canadian Oil Sands (now Suncor) started operation of its mine in 1967, bitumen has been extracted on a commercial scale from the Athabasca Oil Sands by surface mining. In the Athabasca sands there are very large amounts of bitumen covered by little overburden, making surface mining the most efficient method of extracting it. The overburden consists of water-laden muskeg (peat bog) over top of clay and barren sand. The oil sands themselves are typically 40 to 60 metres deep, sitting on top of flat limestone rock. Originally, the sands were mined with draglines and bucket-wheel excavators and moved to the processing plants by conveyor belts. In recent years companies such as Syncrude and Suncor have switched to much cheaper shovel-and-truck operations using the biggest power shovels (100 or more tons) and dump trucks (400 tons) in the world. This has held production costs to around $27 per barrel of synthetic crude oil despite rising energy and labour costs.
After excavation, hot water and caustic soda (NaOH) is added to the sand, and the resulting slurry is piped to the extraction plant where it is agitated and the oil skimmed from the top. Provided that the water chemistry is appropriate to allow bitumen to separate from sand and clay, the combination of hot water and agitation releases bitumen from the oil sand, and allows small air bubbles to attach to the bitumen droplets. The bitumen froth floats to the top of separation vessels, and is further treated to remove residual water and fine solids. Bitumen is much thicker than traditional crude oil, so it must be either mixed with lighter petroleum (either liquid or gas) or chemically split before it can be transported by pipeline for upgrading into synthetic crude oil.
The bitumen is then transported and eventually upgraded into synthetic crude oil. About two tons of oil sands are required to produce one barrel (roughly 1/8 of a ton) of oil. Originally, roughly 75% of the bitumen was recovered from the sand. However, recent enhancements to this method include Tailings Oil Recovery (TOR) units which recover oil from the tailings, Diluent Recovery Units to recover naptha from the froth, Inclined Plate Settlers (IPS) and disc centrifuges. These allow the extraction plants to recover well over 90% of the bitumen in the sand. After oil extraction, the spent sand and other materials are then returned to the mine, which is eventually reclaimed.
Alberta Taciuk Process technology extracts bitumen from oil sands through a dry-retorting. During this process, oil sand is moved through a rotating drum, cracking the bitumen with heat and producing lighter hydrocarbons. Although tested, this technology is not in commercial use yet.
Four oil sands mines are currently in operation and two more (Jackpine and Kearl) are in the initial stages of development. The original Suncor mine opened in 1967, while the Syncrude mine started in 1978, Shell Canada opened its Muskeg River mine (Albian Sands) in 2003 and Canadian Natural Resources Ltd opened its Horizon Project in 2009. New mines under construction or undergoing approval include Shell Canada's, Imperial Oil's Kearl Oil Sands Project, Synenco Energy's, and Suncor's.
It is estimated that approximately 90% of the Alberta oil sands and nearly all of Venezuelan sands are too far below the surface to use open-pit mining. Several in-situ techniques have been developed to extract this oil.
